Famco Chimney Repair Nationwide

Famco Chimney Repair in Yonkers: What to Know First

Famco chimney repair in Yonkers typically runs $285 to $1,900 depending on whether we’re repointing the crown, replacing flashing, or rebuilding the top courses of brick. Most Famco-system repairs are completed in one visit, and you get a written price before any work starts, not after it’s done. This page is for Yonkers homeowners whose Famco caps, dampers, or chimney tops are showing their age: cracked crowns, leaking flashing, spalled brick faces, or dampers that won’t seat. If that sounds like your stack, call (551) 212-3526 and we’ll put a camera up the flue and a number on paper.

Call (551) 212-3526

How Famco Products Fail - and How We Fix Them

Famco makes solid, widely used chimney components. But we’ve seen enough of them in Yonkers to know exactly where they fail, and it’s not always where the homeowner expects. Here’s what we find most often:

• Famco multi-flue caps with rusted mounting brackets. The cap itself may be fine, but the stainless collar and clamp threads corrode after five or six winters of Yonkers freeze-thaw and road salt blowing off the Saw Mill River Parkway corridor. The cap wiggles, the mesh gets one loose corner, and squirrels get in. We replace the bracket with a gauged stainless mount and re-seat the cap, usually same visit. No need to replace a cap that’s still sound.
• Famco top-sealing dampers that won’t fully close. The spring returns on older top-mount dampers get stiff with creosote and soot, and the cable guide starts to bind. You’ll feel it at the lever: it doesn’t snap shut the way it used to. We clean the track, re-lubricate the pivot, and if the spring’s done, we swap in a matching replacement. A damper that won’t seal is a hole in your roof, straight from the furnace up.
• Famco anchor plates with cracked corners. We see this a lot in Yonkers colonials built in the 1960s and 70s. The anchor plate holds the flue liner, and the original cast corners crack from thermal stress over decades. The crack lets water run down the liner and into the smoke chamber. We replace the plate and re-bed the liner with a proper mortar mix, not a quick parge.
• Famco chase covers rusting through on prefab chimney systems. Chase covers on manufactured chimney chases are the first thing to go in Yonkers because the pan sits flat and holds water. Famco’s replacements are galvanized or stainless, but the original often wasn’t. We pull the old pan, inspect the chase top for rot, and flash in a new cover with a proper slope so water runs off, not through.
• Famco damper plates with bent or seized linkage rods. The rod that connects the damper plate to the handle can bend if someone forces the handle against a sticky plate. When that happens, the plate sits slightly open all winter, and the draft pulls heat up the chimney 24 hours a day. We straighten or replace the linkage, and run the camera to confirm the plate seats flat and sealed.

Our Famco Chimney Repair Process

Famco repair in Yonkers shouldn’t be a guessing game, and at Level Two Chimney Yonkers it isn’t. Here’s exactly how a Famco job runs from first call to cleanup:

1. 1
   You call (551) 212-3526. A live person answers, takes your address and what you’re seeing, and we schedule a visit. You’ll get a confirmation text with the tech’s name.
2. 2
   Named tech arrives on schedule, uniformed and background-checked. We look at the Famco component you called about, then run a camera scan down the flue as standard on every visit, not just when something looks wrong.
3. 3
   You get a written diagnosis with photos. We show you the camera footage, point to what failed and why, and put a written price and written scope on paper before anyone starts. Nothing is recommended without evidence you can see for yourself.
4. 4
   Parts decision, transparently. When a part needs replacing, we tell you whether OEM Famco or a quality aftermarket match makes more sense for your setup and budget. We carry common Famco replacements on the truck and source what we don’t through the Haven buying network.
5. 5
   The repair, done to code. Mortar mixed to match your brick, flashing installed with proper overlap, caps seated and sealed. We work clean, and we don’t leave a mess in the yard or on the floor.
6. 6
   Post-repair camera scan and documentation. We run the camera again to confirm the fix, take photos, and hand you the written warranty and photo record before we leave. Every Famco job is covered by the 365-Day Done Right Promise: if it’s not done right, we make it right.

Before

After

What Famco Chimney Repair Costs in Yonkers

Here are the prices we most often quote for Famco work in Yonkers:

• Famco damper replacement or linkage repair: $285 to $520
• Famco cap re-seating with new mounting hardware: $240 to $400
• Famco anchor plate replacement: $650 to $1,100
• Flashing repair around a Famco cap or chase: $480 to $900
• Chase cover replacement, including old pan removal and re-flash: $850 to $1,900 depending on chase size and access

What moves the price is access: a three-story row house chimney on a slope off Nepperhan Avenue costs more to scaffold than a one-story cap in Crestwood. The condition of the underlying brick and mortar matters too, which is why the camera inspection comes first. We never pressure you into work the photos don’t show is needed. Call (551) 212-3526 for a free estimate, in writing, before anything starts.

Why Yonkers Homeowners Call Level Two Chimney Yonkers for Famco Work

The Yonkers homeowner researching chimney repair is already skeptical, and that’s exactly who we built this company for. We don’t ask for trust; we show you the footage. Clause 4 of the Haven Standard requires a documented photo record on every job, and we’ve done it that way since 2009. Over 38,000 chimneys inspected and cleaned, every single one with a written price before work started. We’re an independent Famco service provider, which means we’ll tell you honestly when a part still has life in it and when it doesn’t. Corrine Halstead and her crew have cleaned and inspected stacks from the waterfront near the Hudson River Museum to the narrow row houses off South Broadway. We keep DuraFlex, HeatShield, and Gelco in the multi-brand backup list, so if a Famco part isn’t the right long-term fix, we’ll say so and tell you why. On weekends, Corrine is usually the one at the hardware store debating flue liner gauges with whoever will listen. The camera doesn’t lie, and neither does the quote.

FAQs