Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterCopperfield Chimney Cap & Crown in Yonkers: What to Know First
A Copperfield chimney cap or crown replacement in Yonkers typically runs $340 to $1,800 depending on whether we’re swapping a standard single-flue cap or rebuilding a cracked concrete crown and fitting a custom multi-flue unit. Most Copperfield jobs are done in one visit because we keep the common cap sizes and crown materials stocked on the truck. We’re an independent Copperfield service provider, not a factory warranty station, so we’re free to recommend the fix that actually makes sense for a Yonkers chimney, not the one that moves parts.
If you own a home in Yonkers with a Copperfield cap that’s rusting through, pulling loose, or a crown that’s spalling (concrete flaking off in chunks), call (551) 212-3526. We’ll give you a written price before any work starts.
How Copperfield Products Fail - and How We Fix Them
- Copperfield’s standard galvanized cap bodies rust out at the weld points first. We see this on a lot of the mid-tier Copperfield caps installed across Yonkers in the 2010s. The screened mesh holds up fine, but the corner welds where the lid meets the skirt let water in and rust from the inside out. The cap looks fine from the ground and crumbles when you touch it. We replace it with a Copperfield stainless or a thicker-gauge aftermarket cap and remount it on a new aluminum base.
- Crowns poured too thin during original construction crack and let water into the brick below. This isn’t a Copperfield-specific defect so much as a Yonkers reality: freeze-thaw cycles over the last five winters have wrecked a lot of thin original crowns. When the crown fails, the cap often gets blamed. We rebuild the crown with a proper 2-inch overhang and drip edge, then set the Copperfield cap on a level bed so it actually seals.
- Single-flue Copperfield caps on multi-flue Yonkers chimneys don’t cover the whole crown. Older Yonkers homes often have two flues running side by side. Someone installed a Copperfield cap over one flue and left the other exposed, or stretched a single-flue cap over both. Rain lands directly on the unused flue, or worse, on the crown between flues. We fit a full-width Copperfield multi-flue cap that spans both openings and bolts to the crown with stainless hardware.
- Copperfield caps with hinged lids (the “top-damper” style) seize up from creosote and soot. The hinge pin on these is a known weak point. Over time, creosote works into the pivot and the lid won’t open or close fully, which messes with draft and smear smoke back into the living room. We usually recommend replacing the whole unit with a fixed Copperfield cap rather than fighting the hinge, unless the lid is only a season old.
- Custom Copperfield caps ordered to fit odd Yonkers chimney sizes don’t allow for crown irregularities. Custom caps are built to the measured flue dimensions, but the crown underneath is often wavy or sloped. The cap sits on three points instead of flat, wobbles in the wind, and the mounting brackets fatigue. We level the crown with a thin mortar bed before installing the cap so it doesn’t vibrate itself loose.
Our Copperfield Chimney Cap & Crown Process
- 1
We look at it before we price it. You call (551) 212-3526, we set a visit. A Level Two tech runs a camera down the flue to document the cap, crown, and top-course condition before anything is priced.
- 2
We send you the photos, not just a number. The tech shows you pictures of what’s actually wrong, on the roof and from inside the flue. Clause 4 of the Haven Standard requires the photo record on every job. The camera doesn’t lie, and neither does the quote.
- 3
We put the written price in your hand before any work starts. That includes parts, labor, and what we’ll do if we find hidden damage behind the crown. No change orders by surprise.
- 4
We make the parts call plain. If the Copperfield part is the right fix and available, we use it. If an aftermarket DuraFlex, HeatShield, or Gelco part does the same job better or for less money, we say so and put it in writing.
- 5
We install, photograph, and show you the finished work. Before we leave, you get a documented record of the install: the new cap or crown photographed from the roof, the flue camera pass, and the written warranty.
- 6
365-Day Done Right Promise. If it’s not done right, we make it right. That’s stamped on every job under the Haven Standard.
BeforeAfterWhat Copperfield Chimney Cap & Crown Costs in Yonkers
Here’s what we’re quoting for Copperfield work in Yonkers as of this season:
- Copperfield single-flue cap replacement: $340 to $750, depending on flue size and whether the existing mounting bracket is reusable.
- Copperfield multi-flue cap (custom width): $750 to $1,400, measured and fitted to your crown.
- Crown repair (patch and seal): $250 to $600 for small cracks and surface spalling.
- Full crown rebuild with Copperfield cap install: $1,200 to $1,800 including tear-out, new concrete crown with drip edge, and the cap.
- Crown coating (sealant over a sound crown): $350 to $700, done only if the crown has no structural cracking.
What moves the price: flue count, roof pitch (Yonkers has some steep older roofs), whether the flue liner needs a fitted adapter, and whether the crown needs a full rebuild instead of a patch. Call (551) 212-3526 and we’ll give you a written number, not a ballpark. Estimates are free.
Why Yonkers Homeowners Call Level Two Chimney Yonkers for Copperfield Work
We’re the company that made camera-scan documentation the default back in 2009, years before insurers or regulators asked for it. Every Yonkers job since then has included a photo record under Clause 4 of the Haven Standard. That matters when a Copperfield cap fails close to the roof line in a spot you can’t see from the ground: we show it to you, name the cause, and put the price on paper before any work starts. Written price, written scope, written warranty, every time.
Our techs work on Copperfield caps alongside DuraFlex, HeatShield, and Gelco materials when the job calls for it. We’re not locked into one brand’s catalog. Corrine Halstead runs the Yonkers crew and she’ll put a camera before and after every installation. If you call, a live person answers, 24/7.
FAQs
No, not when we do it. Replacing a failed Copperfield cap with another Copperfield part or a quality aftermarket cap doesn’t void the manufacturer’s warranty on the rest of your chimney system. The warranty covers the original part, not the labor, and most Copperfield caps are out of warranty by the time they rust through anyway. We’ll tell you if the serial number is still covered before you spend anything.
Look for rust at the welds, broken or missing mesh, or a cap that’s shifted off-center from the flue. If the cap body itself is intact but wobbling, we can often reseat it with new hardware for less than $200. If the welds are rusting, replacement is cheaper than patching because the rust is coming from inside the seam.
Yes. Copperfield makes custom-width caps and so do the aftermarket suppliers we work with. We measure the flue opening, the crown width, and the height clearance, then order or fabricate to fit. Multi-flue Yonkers chimneys usually need a custom span, not a stock unit.
Most single-flue cap replacements take under two hours from setup to cleanup. A full crown rebuild with a new cap is a half-day job. We’ll give you the time window in the written quote before you commit, and you’ll get a text when the tech is on the way.
No. A new Copperfield cap stops water from coming in the top, but it won’t repair brick that’s already spalled or a liner that’s already corroded. That’s what we’ll check with the camera before we sell you anything. You’ll see the photos, and we’ll tell you plainly what needs to be fixed now versus what can wait.
We can give you a range, but the written price comes after we see the chimney. What we won’t do is send a tech out to “diagnose” and then surprise you with a number. The price for the job as photographed is the price. If something hidden forces a change, we show you the camera evidence and re-price in writing before touching anything else.
Ready for a real look at your Copperfield cap and crown? Call (551) 212-3526 and we’ll schedule a visit, camera included.
Written by Corrine Halstead, Owner, Level Two Chimney Yonkers at Level Two Chimney Yonkers, serving Yonkers and nearby areas.