Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Yonkers: What to Know First
We’re an independent Olympia Chimney service provider in Yonkers, and we rebuild and reline Olympia Chimney systems on a regular basis. Most liner jobs in Yonkers run $1,800 to $4,200 depending on flue height, liner material, and what the camera shows us before we touch anything. We write the price down before work starts, and that’s been our practice since 2009. If you have an Olympia Chimney fireplace or liner that’s failing, call (551) 212-3526 and we’ll put eyes on it. This page is for Yonkers homeowners who want to know exactly what’s wrong with their Olympia Chimney product and what it costs to fix it.
Key takeaways:
- We service Olympia Chimney liners and rebuilds as an independent provider - not affiliated with or authorized by Olympia Chimney
- Written price before any work starts, every job, no exceptions
- Camera inspection included on every visit, photo record when we’re done
- Free second opinion on any written estimate from a competitor
How Olympia Chimney Products Fail - and How We Fix Them
Olympia Chimney built a reputation in Westchester County for mid-priced masonry and prefab chimney systems that hold up well under routine use. But when they fail, they fail in patterns we’ve learned to recognize the moment the camera comes back up. Here’s what we actually see in the field:
- Ventis Series flashing collar failures - The Ventis line shows up constantly in Yonkers homes built between 2005 and 2015. The flashing collar at the roofline is the first thing to go. Water runs down the outside of the pipe, rusts the chase top, and eventually compromises the chase itself. Most “liner” problems on Ventis units start at the roof, not in the flue. We replace the collar, reseal the chase, and only then address the liner.
- Flex liner kinking on Olympia Chimney flexible liner installs - When an Olympia Chimney flexible liner gets installed too fast or into an offset flue, it kinks behind the damper and blocks draft. The homeowner sees smoke rollout and assumes it’s a clogged chimney. We camera the full run, confirm the kink, and either straighten it or replace it with properly-sized rigid stainless.
- Stainless liner pitting from Yonkers salt air - Yonkers homes within a mile of the Hudson get salt-laden air off the river, and it accelerates pitting in stainless liners. We see it on Olympia Chimney liners that would run another decade further inland. The fix is often a 316L alloy liner rather than the OEM 304 stainless. The original worked fine; the climate here demands better.
- Olympia Chimney damper assembly strain - The OEM damper on many Olympia units gets stiff after ten-plus years of Yonkers heating cycles. When a homeowner forces it open, the linkage bends and the whole assembly shifts. That shift changes liner alignment and can crack the smoke chamber. We service the damper and check the alignment before we recommend a rebuild.
- Smoke chamber cracks behind the finish - Olympia Chimney smoke chambers are parged at the factory, but the parge coat won’t survive a flue liner that’s been run too hot or too long. By the time we see hairline cracks behind the finish, the liner itself is usually thin enough to fail a Level 2 camera inspection. We parge, or we replace the liner and re-parge together.
Our Olympia Chimney Chimney Liner & Rebuild Process
Every Olympia Chimney job runs the same way. No exceptions, no shortcuts. Here’s the sequence:
- 1
Call and scheduling: A live person answers at (551) 212-3526. We book the visit and text you when the tech is en route.
- 2
Level 2 camera inspection: Corrine Halstead or a named tech runs the camera down the full flue and takes readings. You see what we see, on the spot.
- 3
Written report and written price: You get a documented photo record, a plain-English diagnosis, and a written quote for the repair. Nothing starts until you approve it.
- 4
Parts decision: We use OEM Olympia Chimney parts where they’re available and the right call. Where OEM has a known weak point, we won’t reinstall a known failure. DuraFlex, HeatShield, and Gelco all supply quality aftermarket materials we’ve used for years.
- 5
The liner or rebuild: We work down the flue cleanly and test as we go. At the end, the camera goes back down and you get the after-footage.
- 6
Warranty and cleanup: Written warranty in hand, work area clean. The 365-Day Done Right Promise means if it’s not right, we come back and make it right.
BeforeAfterWhat Olympia Chimney Chimney Liner & Rebuild Costs in Yonkers
Yonkers pricing for Olympia Chimney work depends on flue height, liner material, and whether the chase, crown, or smoke chamber needs attention. Here’s what we quote, in writing, before we start:
- Flexible stainless liner replacement (typical single-story Yonkers home): $1,800 - $2,600
- Rigid stainless liner, taller flue or offset: $2,800 - $3,800
- Partial rebuild (crown, top courses, flashing): $2,200 - $4,000
- Full chimney rebuild from the roofline up: $4,500 - $8,000
- Smoke chamber parging and liner reset: $900 - $1,900
What moves the price: roof access difficulty, flue height, existing crown condition, and whether we’re dealing with OEM parts or manufacturing-grade aftermarket that actually outlasts the original. Yonkers rooftops with steep pitches or limited staging space run higher on labor. We’ll quote you a fixed price before any work starts, and we’ll tell you plainly if a repair can wait - that’s not a line, it’s our actual practice. Call (551) 212-3526 and we’ll get you a number.
Why Yonkers Homeowners Call Level Two Chimney Yonkers for Olympia Chimney Work
Because we name the problem and put the price on paper, in that order. Corrine Halstead has been running chimneys in Westchester County for the better part of two decades, and the camera doesn’t lie, and neither does the quote. We don’t do a flashlight look and call it an inspection. Clause 4 of the Haven Standard requires a photo record on every job, and we’ve kept that archive running since 2009 - 38,000-plus chimneys inspected and cleaned, every one with written documentation. Our techs wear uniforms, carry license info, and know Olympia Chimney well enough to tell you when the OEM part is the fix and when a DuraFlex liner or HeatShield repair is the better call. We answer the phone 24/7, we show up on time, and we back every job with the 365-Day Done Right Promise. If you own an Olympia Chimney product in Yonkers, you don’t need a lecture - you need a camera and a quote. We bring both.
FAQs
No. We’re an independent Olympia Chimney service provider in Yonkers. We service Olympia Chimney products but we are not affiliated with or authorized by Olympia Chimney. That independence means we recommend the best fix for your system, even when it means using an aftermarket part that outperforms the OEM.
A stainless steel liner should be camera-inspected every year during your annual chimney sweep, per NFPA 211. In Yonkers, with Hudson River salt air accelerating pitting near the waterfront, we recommend replacing a liner when the camera shows wall thinning of 30% or more, or when creosote buildup won’t clean back to bare metal. Call (551) 212-3526 for a camera check and we’ll show you exactly what’s left of your liner.
Depends on what the camera shows. Small pinholes or seam separation can sometimes be addressed with a HeatShield resurfacing, which runs less than a full liner replacement. But a liner that’s kinked, collapsed, or pitted through in multiple spots is done - and we’ll tell you that in plain words. We’ll never sell you a rebuild you don’t need. You’ll see the footage yourself.
If you’re inside an active Olympia Chimney warranty window, using aftermarket parts is the variable to watch. We use OEM Olympia Chimney parts when the warranty requires it and the OEM part is the right product. When OEM has a known weak point, we’ll flag it and you make the call with the warranty implications in writing. That’s Clause 1 of the Haven Standard: written scope, written price, written warranty, before anyone starts.
We book chimney liner and rebuild work in Yonkers on a seasonal schedule - fall and early winter are the heaviest, and we prioritize systems that are actively unsafe. A live person answers 24/7 at (551) 212-3526. We’ll get you on the calendar, text you when the tech is en route, and hand you a written quote before any work begins. Free estimates, every time.
Written by Corrine Halstead, Owner, Level Two Chimney Yonkers at Level Two Chimney Yonkers, serving Yonkers and nearby areas.